在開啟氣力輸送設備之前，需要先對設備進行檢查，包括齒輪油是否充滿，各部件是否完好，羅茨風機和旋轉供應器的正向反轉以及輸水管道是否順暢等等。
Before starting the pneumatic conveying equipment, it is necessary to inspect the equipment first, including whether the gear oil is full, whether all components are intact, the forward and reverse rotation of the Roots blower and rotary supply, and whether the water pipeline is smooth, etc.
啟動時，應先打開羅茨風機，然后觀察鼓風機出口壓力計的壓力，在管道通暢的情況下，壓力應當基本為零。然后打開一個旋轉供應器，再慢慢打開上面的手動板閥，板閥打開后，材料陷入旋轉供應器，進入輸水管道后，壓力計會發生波動。根據材料的流動性和壓力計的顯示，可以通過調整手動閥門的敞開程度來調整下料量。隨時觀察壓力計的變化。
When starting, the Roots blower should be turned on first, and then the pressure gauge at the outlet of the blower should be observed. With the pipeline unobstructed, the pressure should be basically zero. Then open a rotary supply device, and slowly open the manual plate valve above. After the plate valve opens, the material falls into the rotary supply device, and when it enters the water pipeline, the pressure gauge will fluctuate. According to the fluidity of the material and the display of the pressure gauge, the cutting amount can be adjusted by adjusting the opening degree of the manual valve. Observe the changes in the pressure gauge at any time.
兩臺氣力輸送系統的運輸線在一臺旋轉供給機材料輸送完成后，關閉一臺旋轉供給機，1-2分鐘后從管道輸送材料，然后打開二臺旋轉供給機依次運行。
After the material transportation of two pneumatic conveying systems is completed by one rotary feeder, one rotary feeder is turned off, and after 1-2 minutes, the material is transported through the pipeline. Then, the two rotary feeders are turned on and run in sequence.
關閉設備的時候需要先關閉手動板閥（設備暫時停止的話不必關閉手動板閥），然后關閉旋轉供給器，觀察風扇出口處的壓力計，直到壓力下降到攻關壓力（約1分鐘間隔）。
When shutting down the equipment, it is necessary to first close the manual plate valve (if the equipment is temporarily stopped, there is no need to close the manual plate valve), then turn off the rotary feeder and observe the pressure gauge at the fan outlet until the pressure drops to the breakthrough pressure (approximately 1 minute interval).
設備若是要停止3-4個小時及以上，就需要關閉手動板閥，若是要停止1-2天及以上，需要在除塵結束后關閉手動板閥。
If the equipment needs to stop for 3-4 hours or more, the manual plate valve needs to be closed. If it needs to stop for 1-2 days or more, the manual plate valve needs to be closed after the dust removal is completed.
您的位置:
